Shared Corner has four ways to make its right column read +26. Each way uses two available weights. Try asking what the top row would need in response. That check leaves a single pair and gives you a route through the rest of the board.
Find a useful crossing
Choose Load strategy board in the game or use Practice this example beside the article. Look for Board 2 of 5 · Shared Corner and Edits 0. The fixed weights are 3, 4 and 9. The tray contains 1, 2, 5, 6, 7 and 8.
C1 C2 C3 Row 1 · 3 · Row 2 4 · · Row 3 · · 9
Begin at R1C3, where row 1 and column 3 meet. For both beams the arms run −1, +1, +3. The fixed 9 contributes +27 at the bottom of column 3. To reach +26, the top weight must be one greater than the middle weight. Keep only pairs where both numbers remain in the tray.
In row 1, the fixed 3 contributes +3. The proposed top weight from column 3 would contribute three times its value at R1C3. The weight at R1C1 has to subtract enough to reach +2. If the proposed weight at R1C3 is t, then R1C1 must be 1 + 3t.
| R1C3 | R2C3 | Needed at R1C1 |
|---|---|---|
| 2 | 1 | 7 |
| 6 | 5 | 19 |
| 7 | 6 | 22 |
| 8 | 7 | 25 |
Only the first pair gives an available weight for R1C1. The other three require weights above 9. A larger multiplier puts useful pressure on the decision. Increasing the rightmost weight by one requires three more units of weight at the left end to cancel it.
Reproduce a misleading match
From the starting board, place 6 at R1C3 and 5 at R2C3. Column 3 reads −6 + 5 + 27 = +26. Select Check beams and you will see one of six beams matching and five of nine slots filled.
Now check row 1. Its current reading is +21, with R1C1 as the only blank. That slot would have to subtract 19. Row 2 also fails the test for a possible completion. It reads −7, so its middle weight would have to subtract 12 to reach −19. Both requirements exceed the available weights. Choose Undo last edit twice, or Retry this board, before placing the surviving pair.
Use the surviving pair to finish the board
- Place 2 at R1C3 and 1 at R2C3. Column 3 reaches its target.
- Place 7 at R1C1 to make row 1 read −7 + 3 + 6 = +2.
- Place 8 at R2C2. Row 2 starts this step at −11 from −12 + 1. Its middle arm is −1, so weight 8 takes it to −19.
- Place 6 at R3C1. Column 1 needs +18 more after −7 + 4. The remaining arm is +3.
- Place 5 at R3C2. Column 2 reads −17 before this move, then reaches −12. Row 3 now reads −18 − 5 + 9 = −14.
After the six placements, all the weights are in the grid. The number of matching beams after each placement is 0, 1, 2, 3, 4 and 6. Select Check beams to finish.
Try the same check without placing a weight
Suppose someone suggests putting 2 at R2C3 on the starting board. Which weight would column 3 require above it? Check the fixed weights before you accept the proposal.
Self-check · The required partner
The top weight would have to be 3, because it must exceed the middle weight by one. The only 3 is already fixed at R1C2. Placing 2 at R2C3 cannot lead to a completed board.
This method is easiest when a beam has two empty slots and a crossing beam has only one other empty slot. List pairs from the actual unused weights and check the crossing. With more empty slots in that crossing, several arrangements may still fit. Keep the surviving pairs until you have enough information to rule out the rest.